GE Universal Remote Control CL3 Code List & Setup Guide

GE Universal Remote Control CL3 Code List & Setup Manual

Welcome to the official Best Deal Remotes comprehensive reference guide and master code manual for GE Universal Remotes utilizing the CL3 Code List revision. It is important to note that "CL3" is not a specific remote control model number; rather, it identifies the underlying code firmware library installed inside your GE universal clicker or transmitter handset (manufactured by Jasco). This document contains complete programming instructions, troubleshooting solutions, advanced feature setups, and an extensive code lookup directory organized by device type and brand.

1. How to Identify Your GE Remote Code Revision (CL3)

GE universal remotes (manufactured by Jasco) use specific internal code libraries labeled CL3, CL4, CL5, or CL6. Because code assignments differ between code list revisions, verify that your remote handset requires CL3 codes before entering programming sequences:

1. Remove the battery compartment cover on the back of your GE remote or clicker handset.
2. Remove the AA or AAA batteries to inspect the white factory sticker inside the battery housing cavity or on the inner side of the battery cover door.
3. Look for the version number printed on the label. If it displays "CL3", use the 4-digit codes provided in this guide.
4. Reinsert your fresh alkaline batteries and snap the battery cover back into place.

2. Method 1: Direct Code Entry (Recommended)

Direct code entry is the fastest and most reliable method to program your GE remote handset to your TV, sound system, streaming unit, or cable set-top box. Follow these exact steps:

1. Turn on your target device (such as your TV, Soundbar, Streaming Player, DVD/Blu-ray player, or Cable Box) manually.
2. Press and hold the SETUP button on your GE remote wand until the red indicator light stays on continuously. Release the SETUP button.
3. Press and release the desired device mode button (e.g., TV, AUD, DVD, CBL/SAT). The red indicator light will blink once and remain solid.
4. Enter the 4-digit CL3 code for your brand from the master code tables below.
   • If the code is valid, the red indicator light will turn OFF completely.
   • If the code is invalid, the red indicator light will flash rapidly twice and stay lit. Re-enter the code carefully or try the next code on the brand list.
5. Point the infrared transmitter directly at your device and test basic operations like POWER, VOLUME UP/DOWN, and INPUT.
   • If all functions work properly, setup is complete!
   • If some buttons fail to respond, repeat the setup process using the next listed code for your brand.

3. Method 2: Auto Code Search Procedure

Use Auto Code Search if your equipment brand is not listed in the code tables, or if none of the listed 4-digit codes operate your device:

1. Turn on the device you wish to program.
2. Press and hold the SETUP button until the red indicator light remains lit continuously. Release SETUP.
3. Press and release the appropriate device mode button (e.g., TV, AUD, DVD, CBL).
4. Point the transmitter handset at the device and press the POWER button once. The remote will automatically transmit a batch of 10 codes (the red light blinks once per code sent).
5. If the device turns off, manually press the POWER button to turn it back on, then press and release VOL+ repeatedly until the device responds or toggles off again.
6. Press the same device button (e.g., TV) to lock in and save the working code to memory. The red light will turn off.

4. Advanced Remote Configuration

Master Volume Control Setup

Master Volume Control allows you to lock audio volume functions (VOL+, VOL-, MUTE) exclusively to a primary sound device (e.g., TV or Soundbar receiver) regardless of which device mode (CBL, DVD, AUX) is currently selected on the clicker.

• Lock Volume to a Specific Device: Hold SETUP until the red light stays on → Press the target device button (e.g., AUD or TV) → Press MUTE → Press VOL+. The red indicator blinks twice to confirm the lock.
• Unlock Volume Control: Hold SETUP until the red light stays on → Press the device mode button → Press MUTE → Press VOL-. The red light blinks twice to confirm volume control is unlocked.

Code Retrieval (Blink Out Code)

If you programmed your handset using Auto Code Search and want to retrieve the specific saved 4-digit CL3 code for future reference:

1. Press and hold SETUP until the red light stays on. Release SETUP.
2. Press the target device button (e.g., TV).
3. Press key #1 on the numeric keypad and count the red light blinks (0 blinks indicates digit 0).
4. Repeat the process for keys #2, #3, and #4 to determine each digit of your saved 4-digit code.

5. Factory Reset & High-Intent Troubleshooting

What to Do If Your GE Universal Remote Volume Buttons Stop Working?

If channel or power buttons operate normally but volume buttons fail to respond, the Master Volume Lock is likely assigned to an unconfigured device mode. Restore default volume tracking by unlocking the master volume: Hold SETUP until the red light illuminates, press TV, press MUTE, then press VOL-. The red indicator light will flash twice to confirm volume control is restored back to individual modes.

Why Does the GE Remote Red Indicator Light Flash Twice and Turn Off During Setup?

When the top red light blinks twice rapidly during Direct Code Entry, the 4-digit code entered is not recognized by the internal CL3 library. Check the sticker under the battery compartment cover to confirm your remote specifies "CL3". If verified, try the next alternative code listed for your brand, or use Method 2 (Auto Code Search).

How Do You Factory Reset a GE Universal Remote Control Wand?

If your transmitter becomes unresponsive, buttons lag, or custom setups conflict across media systems, reset the remote to factory settings:

1. Press and hold SETUP until the red indicator light stays on continuously.
2. Press and release the MUTE button.
3. Press and release 0 (zero). The red indicator light will blink twice to confirm the full factory reset.

6. Master GE CL3 Code Lookup Directory

Browse the tables below to look up official 4-digit CL3 codes sorted by hardware device class, provider infrastructure, and brand.

A. Television (TV) CL3 Codes

TV Brand Name	GE CL3 4-Digit Remote Codes
Amazon Fire TV Edition	0205, 0891, 5781, 2014
Apple TV / Digital Media	0891, 0205, 2611
Emerson	0154, 0201, 0180, 0171, 0135, 0405, 0940, 0899
Hisense	0073, 0182, 1660, 1173, 2014, 0216
Insignia	1803, 1829, 1979, 1917, 0135, 0156, 0201
LG	0156, 0178, 0005, 0012, 0050, 0108, 0009
Magnavox	0087, 0207, 0180, 0003, 0020, 0030, 0096, 0398
Panasonic	0180, 0040, 0160, 0540, 0003, 0054, 0062
Philips	0087, 0207, 2552, 0003, 0009, 0012, 0013, 0180
RCA	0003, 0009, 0010, 0015, 0048, 0082, 0096, 0135, 0171
Samsung	0105, 0077, 0009, 0812, 0019, 2051, 0004, 0005, 0012
Sanyo	0154, 0159, 0011, 0048, 0073, 0108, 0180
Sharp	0123, 0147, 0193, 1201, 0004, 0009, 0014, 0028
Sony	0002, 0011, 0080, 5013, 4189, 0000, 0013, 0150
TCL / Roku TV	2014, 4395, 2891, 1741, 6171, 6251, 6001, 5931
Toshiba	0511, 0056, 0811, 1971, 0003, 0012, 0040, 0060, 0154
Vizio	1758, 0178, 0117, 5561, 5611, 0050, 0128

B. Soundbars & Audio Receivers CL3 Codes

Audio Brand Name	GE CL3 4-Digit Remote Codes
Bose	0672, 1284, 0405, 0501, 3708
LG Soundbar	0405, 0501, 1293, 2108, 3212
Panasonic Audio	0308, 0309, 0380, 0405, 0501
Pioneer	0301, 0313, 0501, 1023, 1281
Polk Audio	0405, 0501, 1289, 3412
Samsung Soundbar	0405, 0501, 1304, 2132, 2801
Sony Audio / Soundbar	0300, 0307, 0405, 0501, 1258, 2158
Vizio Soundbar	0405, 0501, 1517, 2451, 3109
Yamaha	0303, 0316, 0405, 0501, 1276, 2112

C. Streaming Media Players CL3 Codes

Streaming Brand Name	GE CL3 4-Digit Remote Codes
Amazon Fire TV Box/Stick	0205, 0891, 5781, 2014
Apple TV	0891, 0205, 2611
Roku Streaming Box / Premiere / Ultra	2014, 4395, 2891, 1741, 5931, 6171, 6251
Sony Media Player	0891, 0402, 0002

D. DVD & Blu-ray Players CL3 Codes

Media Player Brand	GE CL3 4-Digit Remote Codes
Denon	0400, 0421, 0059, 0058
Emerson	0405, 0940, 0899, 0458
LG	0405, 0972, 0907, 0059, 0058
Magnavox	0398, 0408, 0979, 0981, 0980, 0456, 0915
Panasonic	0398, 0419, 0420, 0059, 0058
Philips	0398, 0408, 0423, 0981, 0059, 0058
Pioneer	0399, 0418, 0059, 0058
Samsung	0403, 0418, 0425, 0059, 0058
Sony	0402, 0422, 0427, 0059, 0058
Toshiba	0398, 0404, 0424, 0059, 0058

E. Cable & Satellite Boxes CL3 Codes

Configuring regional cable receivers or satellite boxes across networks in New York, Texas, Florida, California, or nationwide:

Provider / Brand	GE CL3 4-Digit Remote Codes
Comcast / Xfinity	0606, 0707, 1982, 1376, 0812
DIRECTV	0606, 0707, 1377, 0001, 0002
DISH Network	0606, 0707, 1005, 0775, 1170
Spectrum / Charter	0606, 0707, 1877, 0137, 0476
Motorola	0606, 0707, 0476, 1376, 0276
Scientific Atlanta	0606, 0707, 1877, 0877, 0477

7. Quick Reference Problem & Solution Matrix

Observed Issue / Symptom	Immediate Recommended Action
Remote light blinks twice rapidly during code entry	Invalid code. Confirm "CL3" is printed on the label inside battery cavity and try next code.
Power turns TV ON/OFF but volume buttons do not change volume	Reset volume lock by holding SETUP → TV → MUTE → VOL-.
Remote handset does not illuminate when pressing buttons	Replace depleted batteries with fresh AAA or AA alkaline batteries. Check terminals.
Equipment brand is not listed in any table	Use Method 2 (Auto Code Search) to scan the internal library database automatically.

Guide brought to you by Best Deal Remotes (www.bestdealremotes.com) — Your source for replacement remotes, programming guides, and tech support.